FKIE_CVE-2026-87042
Vulnerability from fkie_nvd - Published: 2026-11-10 22:21 - Updated: 2026-11-10 22:21
Severity
Summary
The IEEE 1588 (PTP) port implementation in subsys/net/lib/ptp/port.c adopted the logMessageInterval field of a received Delay_Resp message without any validation. port_delay_resp_msg_process() stored the raw wire value (a full-range int8_t) into port_ds.log_min_delay_req_interval, and that value is later used as a shift count by port_timer_set_timeout() when the Delay_Req timer is armed. Values below about -30 truncate the computed timeout to zero, and values with a magnitude of 64 or more perform an undefined shift of a uint64_t; the standards-defined "not applicable" encoding 0x7F fell into the latter case as well.
PTP messages are received over unauthenticated link-local traffic (UDP multicast on 224.0.1.129, IPv6 multicast, or raw IEEE 802.3), and the handler accepts a Delay_Resp from any sender as long as the port is a time receiver using the end-to-end delay mechanism and the message echoes the port identity and a pending sequence id — both of which the victim itself broadcasts in its Delay_Req. Any node on the same link can therefore inject a single crafted Delay_Resp, or simply become the time transmitter and advertise the bogus interval.
Once the delay timer is armed with a zero timeout, the cooperative PTP thread re-arms and retransmits a Delay_Req on every tick. Each transmission takes a buffer from the fixed CONFIG_PTP_MSG_POLL_SIZE message slab (default 10) and holds it on port->delay_req_list for three seconds, so the slab is emptied within milliseconds and ptp_msg_alloc() then blocks with K_FOREVER inside the only thread that frees those buffers — permanently stalling time synchronization until reboot. Where a transmit-timestamp callback on another thread keeps recycling buffers, the result is instead a sustained multicast Delay_Req flood and continuous CPU consumption. There is no memory corruption and no disclosure of data; the impact is availability of the PTP subsystem and of the local network segment.
The fix rejects intervals outside a representable range and treats 0x7F as "not applicable" as required by IEEE 1588-2019 Table 42. The equivalent unchecked adoption of logMessageInterval from Sync messages in port_sync_msg_process(), a weaker variant of the same issue, is fixed by the companion change 334bf57f416f (#118150), which applies the same range check, ignores the field for unicast Sync messages and treats 0x7F as not applicable.
References
Impacted products
| Vendor | Product | Version |
|---|
{
"affected": [
{
"affectedData": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"subsys/net/lib/ptp/port.c"
],
"programRoutines": [
{
"name": "port_delay_resp_msg_process"
},
{
"name": "port_sync_msg_process"
},
{
"name": "port_timer_set_timeout"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThan": "4.3.2",
"status": "affected",
"version": "3.7.0",
"versionType": "semver"
},
{
"lessThan": "4.5.0",
"status": "affected",
"version": "4.4.0",
"versionType": "semver"
}
]
}
],
"source": "vulnerabilities@zephyrproject.org"
}
],
"cveTags": [],
"descriptions": [
{
"lang": "en",
"value": "The IEEE 1588 (PTP) port implementation in subsys/net/lib/ptp/port.c adopted the logMessageInterval field of a received Delay_Resp message without any validation. port_delay_resp_msg_process() stored the raw wire value (a full-range int8_t) into port_ds.log_min_delay_req_interval, and that value is later used as a shift count by port_timer_set_timeout() when the Delay_Req timer is armed. Values below about -30 truncate the computed timeout to zero, and values with a magnitude of 64 or more perform an undefined shift of a uint64_t; the standards-defined \"not applicable\" encoding 0x7F fell into the latter case as well.\n\nPTP messages are received over unauthenticated link-local traffic (UDP multicast on 224.0.1.129, IPv6 multicast, or raw IEEE 802.3), and the handler accepts a Delay_Resp from any sender as long as the port is a time receiver using the end-to-end delay mechanism and the message echoes the port identity and a pending sequence id \u2014 both of which the victim itself broadcasts in its Delay_Req. Any node on the same link can therefore inject a single crafted Delay_Resp, or simply become the time transmitter and advertise the bogus interval.\n\nOnce the delay timer is armed with a zero timeout, the cooperative PTP thread re-arms and retransmits a Delay_Req on every tick. Each transmission takes a buffer from the fixed CONFIG_PTP_MSG_POLL_SIZE message slab (default 10) and holds it on port-\u003edelay_req_list for three seconds, so the slab is emptied within milliseconds and ptp_msg_alloc() then blocks with K_FOREVER inside the only thread that frees those buffers \u2014 permanently stalling time synchronization until reboot. Where a transmit-timestamp callback on another thread keeps recycling buffers, the result is instead a sustained multicast Delay_Req flood and continuous CPU consumption. There is no memory corruption and no disclosure of data; the impact is availability of the PTP subsystem and of the local network segment.\n\nThe fix rejects intervals outside a representable range and treats 0x7F as \"not applicable\" as required by IEEE 1588-2019 Table 42. The equivalent unchecked adoption of logMessageInterval from Sync messages in port_sync_msg_process(), a weaker variant of the same issue, is fixed by the companion change 334bf57f416f (#118150), which applies the same range check, ignores the field for unicast Sync messages and treats 0x7F as not applicable."
}
],
"id": "CVE-2026-87042",
"lastModified": "2026-11-10T22:21:12.980",
"metrics": {
"cvssMetricV31": [
{
"cvssData": {
"attackComplexity": "LOW",
"attackVector": "ADJACENT_NETWORK",
"availabilityImpact": "HIGH",
"baseScore": 6.5,
"baseSeverity": "MEDIUM",
"confidentialityImpact": "NONE",
"integrityImpact": "NONE",
"privilegesRequired": "NONE",
"scope": "UNCHANGED",
"userInteraction": "NONE",
"vectorString": "CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:N/I:N/A:H",
"version": "3.1"
},
"exploitabilityScore": 2.8,
"impactScore": 3.6,
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
]
},
"published": "2026-11-10T22:21:12.850",
"references": [
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/334bf57f416f2f65745e68db98edf3615ec4e7ab"
},
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/f6b9459f082ac8cc18b7d20a5c4ce1d86b7a55b5"
},
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-cx9q-8hq3-7hpr"
}
],
"sourceIdentifier": "vulnerabilities@zephyrproject.org",
"vulnStatus": "Awaiting Analysis",
"weaknesses": [
{
"description": [
{
"lang": "en",
"value": "CWE-400"
}
],
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
]
}
Loading…
Loading…
Experimental. This forecast is provided for visualization only and may change without notice. Do not use it for operational decisions.
Forecast uses a logistic model when the trend is rising, or an exponential decay model when the trend is falling. Fitted via linearized least squares.
Sightings
| Author | Source | Type | Date | Other |
|---|
Nomenclature
- Seen: The vulnerability was mentioned, discussed, or observed by the user.
- Confirmed: The vulnerability has been validated from an analyst's perspective.
- Published Proof of Concept: A public proof of concept is available for this vulnerability.
- Exploited: The vulnerability was observed as exploited by the user who reported the sighting.
- Patched: The vulnerability was observed as successfully patched by the user who reported the sighting.
- Not exploited: The vulnerability was not observed as exploited by the user who reported the sighting.
- Not confirmed: The user expressed doubt about the validity of the vulnerability.
- Not patched: The vulnerability was not observed as successfully patched by the user who reported the sighting.
Loading…
Loading…
The MITRE ATT&CK techniques below are AI-generated suggestions, inferred from the description of the
vulnerability by the CIRCL/vulnerability-attack-technique-classification-roberta-base
model, served locally by ML-Gateway.
They have not been verified by an analyst and are provided for guidance only.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
Loading…
Related by attack behaviour
Vulnerabilities whose description is nearest to this one in the vector space of the CIRCL/vulnerability-attack-technique-biencoder model. This is a similarity search over the bi-encoder space (plain cosine), not a classification, and it has no measured accuracy.
Loading…