Affected: Alpaquita:stream: linux-lts

In the Linux kernel, the following vulnerability has been resolved:

drm/i915/dmc: Fix an unlikely NULL pointer deference at probe

intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL.

That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init().

However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before.

It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogramming the firmware is a poorly specified sequence and as such unlikely an intentional BIOS behaviour. It's more likely that BIOS is leaving an unintentionally enabled DC6 HW state behind (without actually loading the required DMC firmware for this).

The tracking of the DC6 allowed counter only works if starting / stopping the counter depends on the _SW_ DC6 state vs. the current _HW_ DC6 state (since stopping the counter requires the DC5 counter captured when the counter was started). Thus, usi…

In the Linux kernel, the following vulnerability has been resolved:

drm/i915/dmc: Fix an unlikely NULL pointer deference at probe

intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL.

That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init().

However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before.

It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogramming the firmware is a poorly specified sequence and as such unlikely an intentional BIOS behaviour. It's more likely that BIOS is leaving an unintentionally enabled DC6 HW state behind (without actually loading the required DMC firmware for this).

The tracking of the DC6 allowed counter only works if starting / stopping the counter depends on the _SW_ DC6 state vs. the current _HW_ DC6 state (since stopping the counter requires the DC5 counter captured when the counter was started). Thus, usi…

Affected: Ubuntu:16.04:LTS: linux-hwe-edge, Ubuntu:18.04:LTS: linux-aws-5.0, Ubuntu:18.04:LTS: linux-aws-5.3, Ubuntu:18.04:LTS: linux-azure, Ubuntu:18.04:LTS: linux-azure-5.3, Ubuntu:18.04:LTS: linux-azure-edge, Ubuntu:18.04:LTS: linux-gcp, Ubuntu:18.04:LTS: linux-gcp-5.3, Ubuntu:18.04:LTS: linux-gke-4.15, Ubuntu:18.04:LTS: linux-gke-5.4 and 103 more

In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL. That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init(). However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before. It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogramming the firmware is a poorly specified sequence and as such unlikely an intentional BIOS behaviour. It's more likely that BIOS is leaving an unintentionally enabled DC6 HW state behind (without actually loading the required DMC firmware for this). The tracking of the DC6 allowed counter only works if starting / stopping the counter depends on the _SW_ DC6 state vs. the current _HW_ DC6 state (since stopping the counter requires the DC5 counter captured when the counter was started). Thus, using the…

Ein Angreifer kann mehrere Schwachstellen in Linux Kernel ausnutzen, um unter anderem einen Denial of Service-Angriff auszuführen oder um Sicherheitsmechanismen zu umgehen.