Affected: Alpaquita:25: linux-lts, Alpaquita:stream: linux-lts

In the Linux kernel, the following vulnerability has been resolved:

arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults

contpte_ptep_set_access_flags() compared the gathered ptep_get() value against the requested entry to detect no-ops. ptep_get() ORs AF/dirty from all sub-PTEs in the CONT block, so a dirty sibling can make the target appear already-dirty. When the gathered value matches entry, the function returns 0 even though the target sub-PTE still has PTE_RDONLY set in hardware.

For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered across the CONT range. But page-table walkers that evaluate each descriptor individually (e.g. a CPU without DBM support, or an SMMU without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the unchanged target sub-PTE, causing an infinite fault loop.

Gathering can therefore cause false no-ops when only a sibling has been updated: - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared) - read faults: target still lacks PTE_AF

Fix by checking each sub-PTE against the requested AF/dirty/write state (the same bits consumed by __ptep_set_access_flags()), using raw per-PTE values rather than the gathered ptep_get() view, before returning no-op. Keep using the raw target PTE for the write-bit unfold decision.

Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT range may become t…

In the Linux kernel, the following vulnerability has been resolved:

arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults

contpte_ptep_set_access_flags() compared the gathered ptep_get() value against the requested entry to detect no-ops. ptep_get() ORs AF/dirty from all sub-PTEs in the CONT block, so a dirty sibling can make the target appear already-dirty. When the gathered value matches entry, the function returns 0 even though the target sub-PTE still has PTE_RDONLY set in hardware.

For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered across the CONT range. But page-table walkers that evaluate each descriptor individually (e.g. a CPU without DBM support, or an SMMU without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the unchanged target sub-PTE, causing an infinite fault loop.

Gathering can therefore cause false no-ops when only a sibling has been updated: - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared) - read faults: target still lacks PTE_AF

Fix by checking each sub-PTE against the requested AF/dirty/write state (the same bits consumed by __ptep_set_access_flags()), using raw per-PTE values rather than the gathered ptep_get() view, before returning no-op. Keep using the raw target PTE for the write-bit unfold decision.

Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT range may become t…

Security update for the Linux Kernel

Security update for the Linux Kernel

Affected: Ubuntu:16.04:LTS: linux-hwe-edge, Ubuntu:18.04:LTS: linux-aws-5.0, Ubuntu:18.04:LTS: linux-aws-5.3, Ubuntu:18.04:LTS: linux-azure, Ubuntu:18.04:LTS: linux-azure-5.3, Ubuntu:18.04:LTS: linux-azure-edge, Ubuntu:18.04:LTS: linux-gcp, Ubuntu:18.04:LTS: linux-gcp-5.3, Ubuntu:18.04:LTS: linux-gke-4.15, Ubuntu:18.04:LTS: linux-gke-5.4 and 114 more

In the Linux kernel, the following vulnerability has been resolved: arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults contpte_ptep_set_access_flags() compared the gathered ptep_get() value against the requested entry to detect no-ops. ptep_get() ORs AF/dirty from all sub-PTEs in the CONT block, so a dirty sibling can make the target appear already-dirty. When the gathered value matches entry, the function returns 0 even though the target sub-PTE still has PTE_RDONLY set in hardware. For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered across the CONT range. But page-table walkers that evaluate each descriptor individually (e.g. a CPU without DBM support, or an SMMU without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the unchanged target sub-PTE, causing an infinite fault loop. Gathering can therefore cause false no-ops when only a sibling has been updated: - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared) - read faults: target still lacks PTE_AF Fix by checking each sub-PTE against the requested AF/dirty/write state (the same bits consumed by __ptep_set_access_flags()), using raw per-PTE values rather than the gathered ptep_get() view, before returning no-op. Keep using the raw target PTE for the write-bit unfold decision. Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT range may become the eff…

Ein Angreifer kann mehrere Schwachstellen in Linux Kernel ausnutzen, um einen Denial of Service Angriff durchzuführen oder andere nicht näher spezifizierte Auswirkungen zu erzielen.