Affected: Alpaquita:25: linux-lts, Alpaquita:stream: linux-lts

In the Linux kernel, the following vulnerability has been resolved:

net/mlx5e: RX, Fix XDP multi-buf frag counting for striding RQ

XDP multi-buf programs can modify the layout of the XDP buffer when the program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The referenced commit in the fixes tag corrected the assumption in the mlx5 driver that the XDP buffer layout doesn't change during a program execution. However, this fix introduced another issue: the dropped fragments still need to be counted on the driver side to avoid page fragment reference counting issues.

The issue was discovered by the drivers/net/xdp.py selftest, more specifically the test_xdp_native_tx_mb: - The mlx5 driver allocates a page_pool page and initializes it with a frag counter of 64 (pp_ref_count=64) and the internal frag counter to 0. - The test sends one packet with no payload. - On RX (mlx5e_skb_from_cqe_mpwrq_nonlinear()), mlx5 configures the XDP buffer with the packet data starting in the first fragment which is the page mentioned above. - The XDP program runs and calls bpf_xdp_pull_data() which moves the header into the linear part of the XDP buffer. As the packet doesn't contain more data, the program drops the tail fragment since it no longer contains any payload (pp_ref_count=63). - mlx5 device skips counting this fragment. Internal frag counter remains 0. - mlx5 releases all 64 fragments of the page but page pp_ref_count is 63 => negative reference counting error.…

In the Linux kernel, the following vulnerability has been resolved:

net/mlx5e: RX, Fix XDP multi-buf frag counting for striding RQ

XDP multi-buf programs can modify the layout of the XDP buffer when the program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The referenced commit in the fixes tag corrected the assumption in the mlx5 driver that the XDP buffer layout doesn't change during a program execution. However, this fix introduced another issue: the dropped fragments still need to be counted on the driver side to avoid page fragment reference counting issues.

The issue was discovered by the drivers/net/xdp.py selftest, more specifically the test_xdp_native_tx_mb: - The mlx5 driver allocates a page_pool page and initializes it with a frag counter of 64 (pp_ref_count=64) and the internal frag counter to 0. - The test sends one packet with no payload. - On RX (mlx5e_skb_from_cqe_mpwrq_nonlinear()), mlx5 configures the XDP buffer with the packet data starting in the first fragment which is the page mentioned above. - The XDP program runs and calls bpf_xdp_pull_data() which moves the header into the linear part of the XDP buffer. As the packet doesn't contain more data, the program drops the tail fragment since it no longer contains any payload (pp_ref_count=63). - mlx5 device skips counting this fragment. Internal frag counter remains 0. - mlx5 releases all 64 fragments of the page but page pp_ref_count is 63 => negative reference counting error.…

Affected: openEuler:24.03-LTS-SP3: kernel

The Linux Kernel, the operating system core itself. Security Fix(es):

In the Linux kernel, the following vulnerability has been resolved:

parisc: Drop WARN_ON_ONCE() from flush_cache_vmap

I have observed warning to occassionally trigger.(CVE-2025-39781)

In the Linux kernel, the following vulnerability has been resolved:

MIPS: ftrace: Fix memory corruption when kernel is located beyond 32 bits

Since commit e424054000878 ("MIPS: Tracing: Reduce the overhead of dynamic Function Tracer"), the macro UASM_i_LA_mostly has been used, and this macro can generate more than 2 instructions. At the same time, the code in ftrace assumes that no more than 2 instructions can be generated, which is why it stores them in an int[2] array. However, as previously noted, the macro UASM_i_LA_mostly (and now UASM_i_LA) causes a buffer overflow when _mcount is beyond 32 bits. This leads to corruption of the variables located in the __read_mostly section.

This corruption was observed because the variable __cpu_primary_thread_mask was corrupted, causing a hang very early during boot.

This fix prevents the corruption by avoiding the generation of instructions if they could exceed 2 instructions in length. Fortunately, insn_la_mcount is only used if the instrumented code is located outside the kernel code section, so dynamic ftrace can still be used, albeit in a more limited scope. This is still preferable to corrupting memory and/or crashing the kernel.(CVE-2025-71109)

In the Linu…

Security update for the Linux Kernel

Security update for the Linux Kernel

Affected: Ubuntu:16.04:LTS: linux-hwe-edge, Ubuntu:18.04:LTS: linux-aws-5.0, Ubuntu:18.04:LTS: linux-aws-5.3, Ubuntu:18.04:LTS: linux-azure, Ubuntu:18.04:LTS: linux-azure-5.3, Ubuntu:18.04:LTS: linux-azure-edge, Ubuntu:18.04:LTS: linux-gcp, Ubuntu:18.04:LTS: linux-gcp-5.3, Ubuntu:18.04:LTS: linux-gke-4.15, Ubuntu:18.04:LTS: linux-gke-5.4 and 138 more

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: RX, Fix XDP multi-buf frag counting for striding RQ XDP multi-buf programs can modify the layout of the XDP buffer when the program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The referenced commit in the fixes tag corrected the assumption in the mlx5 driver that the XDP buffer layout doesn't change during a program execution. However, this fix introduced another issue: the dropped fragments still need to be counted on the driver side to avoid page fragment reference counting issues. The issue was discovered by the drivers/net/xdp.py selftest, more specifically the test_xdp_native_tx_mb: - The mlx5 driver allocates a page_pool page and initializes it with a frag counter of 64 (pp_ref_count=64) and the internal frag counter to 0. - The test sends one packet with no payload. - On RX (mlx5e_skb_from_cqe_mpwrq_nonlinear()), mlx5 configures the XDP buffer with the packet data starting in the first fragment which is the page mentioned above. - The XDP program runs and calls bpf_xdp_pull_data() which moves the header into the linear part of the XDP buffer. As the packet doesn't contain more data, the program drops the tail fragment since it no longer contains any payload (pp_ref_count=63). - mlx5 device skips counting this fragment. Internal frag counter remains 0. - mlx5 releases all 64 fragments of the page but page pp_ref_count is 63 => negative reference counting error. Resu…

Ein Angreifer kann mehrere Schwachstellen im Linux Kernel ausnutzen, um einen nicht näher spezifizierten Angriff durchzuführen, möglicherweise Sicherheitsmaßnahmen zu umgehen, Daten zu manipulieren oder offenzulegen oder einen Denial-of-Service-Zustand zu verursachen.