Affected: Alpaquita:23: linux-lts, Alpaquita:stream: linux-lts

In the Linux kernel, the following vulnerability has been resolved:

can: gs_usb: fix time stamp counter initialization

If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback.

In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host.

At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host.

However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early.

Move the gs_usb_timestamp_init() function before the…

In the Linux kernel, the following vulnerability has been resolved:

can: gs_usb: fix time stamp counter initialization

If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback.

In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host.

At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host.

However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early.

Move the gs_usb_timestamp_init() function before the…

Security update for the Linux Kernel

Affected: Ubuntu:16.04:LTS: linux-hwe-edge, Ubuntu:18.04:LTS: linux-aws-5.0, Ubuntu:18.04:LTS: linux-aws-5.3, Ubuntu:18.04:LTS: linux-azure, Ubuntu:18.04:LTS: linux-azure-5.3, Ubuntu:18.04:LTS: linux-azure-edge, Ubuntu:18.04:LTS: linux-gcp, Ubuntu:18.04:LTS: linux-gcp-5.3, Ubuntu:18.04:LTS: linux-gke-4.15, Ubuntu:18.04:LTS: linux-gke-5.4 and 78 more

In the Linux kernel, the following vulnerability has been resolved: can: gs_usb: fix time stamp counter initialization If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback. In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host. At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host. However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early. Move the gs_usb_timestamp_init() function before the URBs…

Ein Angreifer kann mehrere Schwachstellen im Linux Kernel ausnutzen, um einen Denial of Service Angriff durchzuführen und um nicht nähere beschriebene Effekte zu verursachen.